The post Protected: PRIVATE: FETCHING BUG REPORTS (ESPER) first appeared on .

Printer

“Printer out of Paper” – inserting paper into printer

The screen shows “PRINTER OUT OF PAPER” if there is no paper-roll.

We must refill the paper-roll into the printer slot when the printer runs out of paper.

Please follow these steps below.

Step 1) Removing:

Remove the blue shaft from the printer by pressing both ends, discard old paper-roll.

Step 2) Adding:

Insert the blue shaft in the new paper-roll as shown, place the shaft by pressing the shaft on both sides into the printer slot.

Step 3) Inserting:

Feed the paper into the printer.

Go to the dashboard page and tap on the TestPrint button.

To clear the Paper Jam

Use old Credit/Debit/Visiting cards to clear the jam/paper struck inside the printer.

Follow these steps to clear the paper jam.

Step 1)

Cut the paper with a scissor.

Step 2)

Press the clip at bottom and lift the printer as shown.

Step 3)

Rotating the side knob and removing jammed paper-roll.

Step 4)

Clear all pieces of paper inside the printer slot with the help of a card. Again check for any left over pieces of paper, and clean it completely.

Step 5)

Bring the printer part to its original position as shown.

Step 6)

Feed the paper end into the printer, the printer will automatically pull the paper.Then tap on dashboard,tap on ‘Test Print’ to verify.

How to avoid “Paper Jam”?

Instruct to customers/users

• Not to close the paper outlet during the receipt printing.
• Make sure to use good quality paper-rolls
• Low quality or thin papers are prone to being struck leading to paper jam.
• Periodically clean the printer slot from unused cards.

Instruct to customers/users

• When filling the paper-roll, check the direction of paper insertion. If the paper is inserted crosswise into the printer slot, It leads to paper jam.

Menu

How to turn off/on the item and category

Turn off the item by tapping on the blue toggle button. Turn on the item by tapping on the toggle button. verify after closing the door

Turn off the category by tapping on the green toggle button. Turn on the category by tapping on the toggle button.

verify after closing the door

Can We Schedule the item or category along with day and time?

Note:- The scheduling can be modified only through logging into qsr-lite cloud application.

You can view the scheduled day and time for a particular item.

You can view the scheduled day and time for a particular item.

Order

How to check payment status of an order

Any confusion after ordering can be verified by looking at the “orders” page.

The orders page clearly indicates 3 payment status – completed, pending, and failed payments.

Go to the orders page by opening the door and tapping on “orders”.

To view the particular order details tap on the “blue view” button .

• The Order page is visible as shown.

To view the particular order details tap on the “blue view” button .

You can view pending payments here.

• tap-on the pending transaction to verify.
• Result of pending payment is displayed as completed/failed.

To view the particular order details tap on the “blue view” button .

You can view the failed payment here.

• Failed status indicates,failed transaction,so no bill is generated.

To view the particular order details tap on the “blue view” button.

You can view completed payment here.

If you want the printout of the bill, tap on the blue print button.

Internet

What is Receipt does not print after completion of transaction

These situations occur for the following reasons.

• Network issues.
• Shortage of paper in printer-roll.
• Payment process failed.

Why didn’t the self ordering application launch?

Restart the machine by switching-off and switching-on once,

If the problem persists, which happens due to poor network connection. Contact service team @selfserve.

END…

The post GSS help page first appeared on .

 View after Installation.

The post GO self serve kiosk installation guide video first appeared on .

The post Protected: Signage Soft guide first appeared on .

The post Protected: QSR Access user guide first appeared on .

The post Protected: Configuring VPN first appeared on .

 Instruction manual for installation

– Unbox the device and components.

– Locate the floor stand assembly guide and allen key wrapped with the floor stand.

–Unscrew the screw at the bottom of the floor stand.

 

Floor stand should be screwed along with the base plate with front side of base plate to front bottom of the floor stand , tighten the screws well with allen key.

                                              

                                                                                                   

• Unscrew the screw at the bottom of the floor stand.

 

       

 

• Floor stand should be screwed along with the base plate with front side of base plate to front bottom of the floor stand , tighten the screws well with allen key.

                                  

• Unscrew the four(4) screws on the back side of the display and fix the clamp plate to it , the sticker indicating top should be towards the manufacturing sticker or antenna side of display , tighten the screws very well with allen key.

 

                                   

 

• Find the adapter provided inside the box

– Unscrew the screw at the bottom of the floor stand.

– Screw the floor stand along with the base plate, ensuring that the front side of the base plate is facing the front bottom of the floor stand. Tighten the screws well with an allen key.

– Unscrew the four screws on the back side of the display.

– Fix the clamp plate to the display, making sure that the sticker indicating top is towards the manufacturing sticker or antenna side of the display.

– Tighten the screws very well with an allen key.

                    

• Connect the power cable to the adapter and make the adapter go inside the floor stand and take the power connecting (3 pin) end outside the stand with the small cut out in back bottom side of stand, leave the display connecting adapter pin on top side of stand for connecting to display.

 

                                

• Unscrew the screws on top both sides of the floor stand and align the display clamp and screw the display clamp plate with floor stand and screw well with allen key.

                                          

• Connect the power cable to the display socket and power on the switch.

 

             

 

                               

 

• This is the final look of the whole unit after the display is mounted to the floor stand.

THANK YOU !

 

The post Instruction manual for installation first appeared on .

The post Protected: Go SelfServe kiosk screen first appeared on .

The post Protected: SignageSoft user Guide first appeared on .